Start motor
Moderator: gk
Start motor
My engine must be cursed...
Today it did not start. Star motor is turning but engine is not. I took starter of and inspected tooths on it and on next wheel. Both ok. Anyone have experienced the same?
Today it did not start. Star motor is turning but engine is not. I took starter of and inspected tooths on it and on next wheel. Both ok. Anyone have experienced the same?
Br,
Vesa
Vesa
Hi Vesa,
i already had this problem, see
http://www.ital-web.de/forum/viewtopic. ... &start=915
Problem is the freewheel, Position No 21.
Good luck
Siggi
i already had this problem, see
http://www.ital-web.de/forum/viewtopic. ... &start=915
Problem is the freewheel, Position No 21.
Good luck
Siggi
You have to dismantle the left engine cover and pull off the flywheel with a puller and by heating it up quite well. The free wheel is fixed with screws at the inner site of the flywheel. I also changed the gear pos 26.
These parts i got out of an engine with destroyed c-heads i bought many years ago.
Maybe Olli Thiel is able to help you, he`s got a good stock of used parts
www.thiel-motorsport.de
Regards
Siggi
These parts i got out of an engine with destroyed c-heads i bought many years ago.
Maybe Olli Thiel is able to help you, he`s got a good stock of used parts
www.thiel-motorsport.de
Regards
Siggi
At last it is opened. Quality of original screws is not too high. Quite likely will subtitute them with heavy duty ones.
Luckily nothing is broken and i got broken screw pieces of and Marc at https://www.motostretta.com has freewheel in stock. But i still believe freewheel is from some other bike, and can be found locally.
Luckily nothing is broken and i got broken screw pieces of and Marc at https://www.motostretta.com has freewheel in stock. But i still believe freewheel is from some other bike, and can be found locally.
- Dateianhänge
-
- start.png (242.93 KiB) 8307 mal betrachtet
Br,
Vesa
Vesa
Re: Start motor
Free wheel was not broken, but a bit worn out, so it will be replaced. Cost is under 100e
And screws i will substitute with stronger ones, unless there is good reason reason to use std bolts...?
And screws i will substitute with stronger ones, unless there is good reason reason to use std bolts...?
Zuletzt geändert von VesaII am Mittwoch 12. Mai 2021, 09:01, insgesamt 8-mal geändert.
Br,
Vesa
Vesa
Re: Start motor
Now even brush bridge is replaced, but it was hard to find and did not fit straight in as it sure is china made. Spring was too high (arrow) and cause of this rotor did not fit in place. Replaced it with original one. Now everything startmotor related should be fixed.
- Dateianhänge
-
- hiilet.png (242.16 KiB) 7745 mal betrachtet
Zuletzt geändert von VesaII am Freitag 7. Mai 2021, 18:33, insgesamt 6-mal geändert.
Br,
Vesa
Vesa
Re: Start motor
Did start the motor today and with no problems
Not sure, but i feel root cause was worn out brushes and when start motor did not get enough current, then starting became jerky. This caused weak std freewheel bolts go off, one by one.
Conclusion: It is not bad idea to change starter brushes and free wheel with bolts same time as you change cam chain.
Putting starter together is a bit tricky. You need to be careful and check play is ok and motor turns freely. Do polish contactor surface well. Do not leave it coarse as brushes will wear out more rapidly.
Not sure, but i feel root cause was worn out brushes and when start motor did not get enough current, then starting became jerky. This caused weak std freewheel bolts go off, one by one.
Conclusion: It is not bad idea to change starter brushes and free wheel with bolts same time as you change cam chain.
Putting starter together is a bit tricky. You need to be careful and check play is ok and motor turns freely. Do polish contactor surface well. Do not leave it coarse as brushes will wear out more rapidly.
Br,
Vesa
Vesa
Re: Start motor
Forgot to mention...
One scary thing is to remove flywheel, but last time used Air Impact Wrench as they use when removing and tightening car wheel nuts professionally. Works like charm with some heat and proper puller.
One scary thing is to remove flywheel, but last time used Air Impact Wrench as they use when removing and tightening car wheel nuts professionally. Works like charm with some heat and proper puller.
Br,
Vesa
Vesa